Skyline Transport Group

Flatbed freight: what to have ready before the truck arrives

Dimensions and weight told straight, tarping decided at quote time, securement points, and why a bad dimension quote becomes a permit problem.

· 9 min read · By the Skyline Transport Group team

Open deck is less forgiving than a van, and almost all of the difficulty is front-loaded. A flatbed load that has its dimensions, weight, securement and tarping settled at quote time is an ordinary load. The same freight with any of those four discovered at the dock is a delay, a re-quote, or a truck that leaves empty.

Dimensions, told straight

Length, width and height of the piece as it will sit on the deck, plus the weight. Not the crate size from a catalog, not the dimensions before the skid was built, and not a rounded-down number because the real one sounded like it might be a problem.

The reason to be exact is that these numbers decide the legal question, not the pricing question. A standard flat deck sits about sixty inches off the ground, so a piece over roughly eight and a half feet tall is already at the legal height limit before you account for the road. A step deck's lower deck sits around thirty-eight to forty-two inches, which buys you back about a foot and a half of height. Which trailer you need is arithmetic on your numbers.

Why a bad dimension becomes a permit problem

Legal dimensions on most routes are 8 ft 6 in wide, 13 ft 6 in high in many states, and 48 to 53 ft long, with weight limits by axle configuration. Cross any one of them and the load needs a permit, and permits are per state, filed in advance, with lead times.

So a piece quoted at 8 ft 4 in wide and measured at 8 ft 8 in at the dock is not a small discrepancy. It has converted a legal load into a permitted one, which means the truck cannot legally leave, the permits take hours or days depending on the states, and the escort requirement may have changed too. This is the single most common way a flatbed load falls apart, and it is always a measurement nobody rechecked.

Measure the loaded silhouette, not the part

Height is measured from the ground with the piece on the deck, which means deck height plus dunnage plus the piece. Width is measured at the widest point including anything that protrudes. If a fitting, a flange or a bracket sticks out four inches, the load is four inches wider.

Tarping, decided at quote time

Tarping is physical work, it takes a driver forty minutes to an hour, and it is paid. It is also the thing most often left off a tender and then demanded at the dock, which is how a load ends up with a driver who does not have tarps on the truck and a shipper who is certain they said so.

What to settle up front: whether the load must be tarped at all, how many tarps, whether it is a full tarp or a partial, and who supplies them. If the freight is weather-sensitive, say so at quote time and it becomes a line on the rate confirmation instead of an argument.

Securement, and what the driver is legally responsible for

Federal securement rules assign the driver responsibility for how the load is secured, which is why a driver may refuse a load they cannot secure properly. That is not a driver being difficult. It is a driver declining to be the party holding the violation.

The shipper's part is making securement possible:

Named tie-down or lifting points on the piece, or a drawing that shows where load can be taken.

Dunnage, blocking or cribbing if the piece needs to sit off the deck or cannot take a chain directly.

Edge protection where a strap crosses a sharp corner, which is usually cheaper for the shipper to supply than for the driver to improvise.

A statement of anything that must not be chained: polished surfaces, coated steel, glass, machined faces.

Loading, and who does it

Open deck loading is usually a crane or a forklift and it is usually the shipper's. Settle before dispatch who is lifting, whether the driver is expected to assist, and what the loading window is, because a crane booked for an hour is a different appointment from a forklift available all afternoon.

Ask also whether the piece can be loaded in more than one orientation. Turning a long piece across the deck instead of along it occasionally solves a width problem, and occasionally creates one.

Weight distribution, not just total weight

A load can be under the gross limit and still be illegal, because weight is regulated per axle group as well as in total. A heavy piece sitting too far forward or too far back on a deck overloads one axle group while the total looks fine, and the driver finds out at the first scale.

What the shipper can do about it is tell us where the weight sits in the piece. A machine whose mass sits at one end behaves nothing like a uniformly loaded deck, and a single sentence about that at quote time lets the driver plan where to place it. The alternative is repositioning a forty-thousand-pound object in a parking lot, which needs equipment the driver does not have.

The paperwork that travels with open deck

A bill of lading with the real piece count, dimensions and weight, since this is the document a scale or an inspector reads.

Any permit numbers, if the load is over dimension, and the permitted route.

Photographs of the loaded and secured freight before departure. Ten seconds of phone camera has settled more open deck damage claims than any clause.

What we do with the numbers you give us

We run them against legal limits for the route before quoting, so you find out at quote time whether the load is legal, permitted, or permitted with escorts. If it is over dimension we file the permits for every state on the route ourselves and state the lead time before you commit to a delivery date.

If the numbers turn out wrong at the dock we will tell you what changed and what it now requires. What we will not do is put a driver on the road illegal and hope the scales are closed.

Send the dimensions, the weight, the tie-down points and whether it needs tarping, and you will get a quote you can plan around. Flatbed and step deck has the deck heights and legal weights.

Sources

  • FMCSA, Protection Against Shifting and Falling Cargo (49 CFR 393, Subpart I)
  • Skyline Transport Group open deck quoting procedure, current revision